As a golfer, having a comfortable and properly fitting putter grip is essential for a smooth and controlled stroke. If you’re looking to replace your old putter grip with a new one, fear not!
This guide will walk you through the process on how to change a putter grip in simple steps, assuming no prior experience.
By following these instructions, you’ll have a fresh grip on your club and be ready to improve your game in no time.
Some of the links in this post are affiliate links. This means that if you click on the link and purchase the item, I may receive an affiliate commission at no extra cost to you. All opinions remain my own.
Step-by-Step Instructions To Change Putter Grip At Home
Estimated Time to Complete: Approximately 30 minutes for regripping your putter.
At a high level, here is the summary of the steps to re-grip a putter.
If you aren’t sure why you should change your putter grip, skip down to this section Why Regrip Your Putter?
- Remove the old putter grip – remove the old grip without damaging your club and the cap from the end of the grip
- Clean your putter – clean the old tape off the putter shaft
- Prepare the new grip – apply double-sided tape to the club shaft
- Install the new grip – pour grip solvent inside of the grip, slide the grip onto the shaft, and twist the putter grip to align
- Let the new grip dry – for a putter we recommend 24 hours
That is all it takes to change a putter grip! It is really easy once you do it a few times. Don’t be overwhelmed by it, once you get going, you will see how simple this is.
Materials Needed TO Change a Putter Grip
(See section at end of post for links to all materials needed to change a putter grip)
- New putter grip
- Double-sided grip tape
- Golf grip solvent or rubbing alcohol
- A bucket or container
- Utility knife or grip cutter
- Clean cloth or towel
- Gripping station or vise (optional)
- Grip solvent applicator (optional)
Step 1: Remove the Old Putter Grip
(Approximately 10 minutes)
- Lay your golf club horizontally on a flat surface, ensuring the clubhead is secure and won’t move.
- If your old grip has a cap on the end, gently remove it using a utility knife or grip cutter.
- Pour a small amount of grip solvent or rubbing alcohol into the bucket or container.
- Apply grip solvent or rubbing alcohol inside the old grip and twist it to break the bond between the grip and the club shaft.
- Slowly slide the grip off the club, twisting it gently if needed. Be patient and avoid pulling too hard, as it may damage the club.
Step 2: Clean the Club Shaft with Grip Solvent
(Approximately 5 minutes)
- Take a clean cloth or towel and moisten it with grip solvent or rubbing alcohol.
- Wipe the club shaft thoroughly to remove any old adhesive or residue from the previous grip.
- Allow the shaft to dry completely before proceeding to the next step.
Step 3: Prepare the New Grip
(Approximately 5 minutes)
- Unwrap the new putter grip from its packaging.
- Check the grip for any alignment markings or patterns you prefer in a specific position.
- Apply double-sided grip tape to the club shaft, starting from the top and wrapping it downward in a spiral motion. Overlap the tape slightly with each turn, ensuring full coverage.
- Trim the excess tape with a utility knife or grip cutter, leaving a neat, clean edge.
Step 4: Install the New Grip
(Approximately 10 minutes)
- Pour a small amount of grip solvent or rubbing alcohol inside the new grip.
- Quickly rotate the grip, ensuring the solvent or alcohol spreads evenly throughout the grip’s inner surface.
- Align the grip with the desired positioning (based on any markings or patterns) and slide it onto the club shaft in a straight and steady motion.
- Push the grip firmly against a hard surface, such as the floor or a countertop, to ensure it’s fully seated on the club shaft.
- Wipe away any excess grip solvent or rubbing alcohol with a clean cloth or towel.
Step 5: Let the New Grip Dry
Allow the grip to dry and set for at least 24 hours before using the club.
You can start using it after 4 hours, but there is a slight risk of the grip moving. For a putter we recommend waiting a day due to the importance of alignment.
Conclusion
Congratulations! You’ve successfully installed a new putter grip on your golf club. By following these simple steps, you’ve improved the comfort of your club and set the stage for better putting performance.
Remember to take your time during the process, ensuring a clean and secure grip installation. Get out there, practice your putting, and enjoy your improved golf game!